Fuel Oil Disc Separator - Centrifuge , Solid Liquid Separation
Model PDSD8000 separator is mainly used to remove water and
mechanical impurities from diesel oil, lubricating oil and other
mineral oil in marine diesel engine unit and land-used diesel
generator unit of power station so as to reduce wear of the diesel
engine and other machine, and prolong engine life. The model is
also used to separate two unsolvable liquids with different
specific gravity or remove small amount of solid particle from
The machine adopts automatic control, and has the advantages of
high efficiency, low oil consumption, convenient operation and
economic maintenance cost.
The clear oil and dirty water are pumped out by centripetal pump,
the sludge is discharged automatically and fully.
The machine is one kind of rotary machine with high speed. After
accurate dynamic balancing, it can run for long time with low
vibration, safety and security.
The design, product and acceptance are conformed to the standard of
GB/T5745 “Marine Disc Separator”.
Main Technical Specification for single machine
Output pressure of clear oil
L × W × H (mm)
1150 × 900 × 1500
Automatic control system
Water Control: Automatic control unlocking water, sealing water and
Pneumatic Control: Filter and adjust compressed air, control
three-way changeover pneumatic valve.
Temperature Control: Automatic control the temperature of the oil
line, also control separately
or with electric control cabinet at the same time.
Buzzer Control: Monitor oil temperature, pressure, over loading,
non-discharging and leaking,
and Offer a group of passive contactor stretching out to control
The whole unit consists of
2. Electric control box
3. Oil feed pump
4. Oil filter
5. Pneumatic three-way valve
6. Ball valve
7. Pressure gauge
8. Vacuum gauge
9. Stop-check valve
10. 2/2 Solenoid valve
11. 3/2 Solenoid valve
12. Air reduction pressure valve
13. Brass filter ball valve
14. Water pressure reducing valve
15. Temperature sensor
16. Liquid level switch
17. Sludge pump
1. According to the requirements of each classification society,
all modules are equipped with oil leak alarm and high temperature
2. Oil.hydraulic,pneumatic control part adopts the Brand Baode
3. Heater adopts brand SWEP (Germany).
4. Pressure control adopts Korean products or WIKA products
5. Screw pump is used instead of gear pump.
6. All equipped with automatic temperature control device (Made by
the RTK production in Germany or made in China)
7. The main electrical components of standard electrical control
box are produced by Schneider company while PLC is produced by
Siemens or Mitsubishi.
8. The complete sets referred above are all Peony's production of
automatic Standard Controls and we certainly can modify the
configuration list according to customers’ specified requirements.
Peony organizes the model selection question as below
1)How many kinds of the oil can you separate?
This series separator is widely used for kinds of oils, especially
for the Marine diesel oil and the similar
oil, such as light fuel oil, heavy fuel oil, lubrication oil, steam
turbine oil, detergence oil, engine oil etc
2)How can you select the suitable capacity?
Different oil has different capacity, our 1500L, 2000L, 3000L,
4000L, 5000L, 6000L, 8000L,
10000L capacity is for the Marine diesel oil 0# as sample. It also
depends on the viscidity, temperature,
and for all the capacity model, we have an oil characteristic sheet
to help our customer to find out
what their oil is, and what capacity their oil belongs to.
3) Is your separator self cleaning?
We have 3 types discharge means according to different material and
we have self cleaning model and manual cleaning model.
1. Manual discharge model for the oil with very less solid
2. Full discharge model for the big capacity treatment and a little
3. Partly discharge model for the bigger capacity treatment and
more solid component
4).Variable discharge model
No.full discharge type and partially discharge type are both self
4)Will you help us to select the model?
Yes,you can select the model by yourself, or as long as you provide
your material characteristic,
we have professional engineer team to help you select the suitable
5)Do you only have the single machine or the unit?
Both we have.
Peony Centrifuge has been dedicated to producing machinery and
equipments and carrying out facility construction, pursuing the
best quality and producing the best product at the same time.
We are committed to reward you with a better quality in return for
our interest in and faith toward.
We will do our utmost for one more stepping forward, based on our
infinite services and trust to customers.